- inCAD Library Home
- > No.000217 Low Impact Clamping Mechanism
No.000217 Low Impact Clamping Mechanism
34
34
Low-impact clamp
Related Category
Stopper Bolts
| Product name | Stopper Bolts with Bumpers/Straight Type |
|---|---|
| Part number | PUSS10-40 |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
Use the stopper bolts with resin tip as workpiece clamp components. Worn out items can be replaced easily.
Available sizes
■Stopper Bolts With Bumpers- Straight Type
| Stopper | Hex Screw | Accessory (Hex Nut) | ||||
|---|---|---|---|---|---|---|
| Material | Hardness | Material | Strength classification | Surface Treatment | Material | Surface Treatment |
| Urethane(Black) | Shore A90 | EN 1.7220 Equiv. | 10.9 | Trivalent Chromate | EN 1.0038 Equiv. | Trivalent Chromate |
| EN 1.4301 Equiv. | - | - | EN 1.4301 Equiv. | - | ||
| Polyacetal(White) | - | EN 1.7220 Equiv. | 10.9 | Trivalent Chromate | EN 1.0038 Equiv. | Trivalent Chromate |
| EN 1.4301 Equiv. | - | - | EN 1.4301 Equiv. | - | ||
■Sizes and Dimensions
| Screw Dia. (Coarse) | Thread Length (Selectable) | Stopper Section Length | Stopper Section Dia. | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 | 50 | 60 | 70 | |||
| 4 | ○ | ○ | ○ | ○ | ○ | ○ | - | - | - | - | - | 4.5 | 3.1 |
| 5 | ○ | ○ | ○ | ○ | ○ | ○ | ○ | - | - | - | - | 4 | |
| 6 | - | ○ | ○ | ○ | ○ | ○ | ○ | ○ | ○ | ○ | - | 4.8 | |
| 8 | - | - | - | ○ | ○ | ○ | ○ | ○ | ○ | ○ | - | 5.5 | 6.5 |
| 10 | - | - | - | - | ○ | ○ | ○ | ○ | ○ | ○ | ○ | 8.3 | |
| 12 | - | - | - | - | ○ | - | ○ | - | ○ | ○ | ○ | 6 | 10 |
Plastic Knobs
| Product name | Plastic Knobs/Mushroom Shaped |
|---|---|
| Part number | NMM6-25 |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
Highly efficient knob can be mounted economically
Available sizes
■Plastic Knobs - Mushroom Shaped
| Screw | Knob | Screw | |
|---|---|---|---|
| Material | Material | Surface Treatment | |
| Threaded | Phenolic Resin (Black) | EN 1.0715 Equiv. | Trivalent Chromate |
| Tapped | Brass (Insert) | - | |
■Sizes and Dimensions
| Screw | Thread Length | Knob O.D. | Mounting Height | ||
|---|---|---|---|---|---|
| Type | Dia (Coarse) | Threaded | Tapped | ||
| Threaded ･ Tapped | M5 | 10 | 7 | Ø17 | 15 |
| M6 | 11 | Ø21 | 18 | ||
| Ø25 | 22 | ||||
| M8 | 15 | 12 | Ø33 | 30 | |
Square Resin Washer
| Product name | Square Resin Washers/POM/MC Nylon |
|---|---|
| Part number | WSRPM20-40-20 |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
Best suited for securing workpiece without damaging
Available sizes
■Square Resin Washers
| Material | Color |
|---|---|
| Polyacetal | White |
| MC Nylon Standard Grade | Blue |
■Sizes and Dimensions
| Width | Length (1mm increment) | Hole pitch (0.5mm increment) (hole pitch ≤ width - hole position from end face) | Thickness | Screw Nominal Dia. | Hole position from end face |
|---|---|---|---|---|---|
| 10 | 20-40 | 10.0-30.0 | 3 | 3 | 5 |
| 12 | 24-46 | 12.0-36.0 | 4 | 4 | 6 |
| 15 | 30-60 | 15.0-45.0 | 4 | 5 | 7.5 |
| 20 | 40-80 | 20.0-60.0 | 5 | 6 | 10 |
| 25 | 50-100 | 25.0-75.0 | 6 | 8 | 12.5 |
Accuracy Info
■The accuracy of square resin washer
| Width tolerance | ±0.3 |
|---|---|
| Hole pitch tolerance | ±0.1 |
| Length tolerance | ±0.3 |
| Thickness tolerance | ±0.1 |
IDEA NOTE Impact Proof Clamping
Unnecessary impact is avoided by using a slide shaft with tapered portions.
IDEA NOTE Clamping position is retained by stopper cam.
In the clamping position, the stopper cam fixes the slide shaft. In this state, the only way to unclamp is to first release the cam by operating the knob.
-
TERMS AND CONDITIONS FOR USE OF CAD DATA-
Your access to the CAD data that MISUMI Corporation (hereinafter referred to as the Company) posts on this site (including 3D CAD data, intermediate 3D CAD data and 2D CAD data; hereinafter referred to as the Data) are of products manufactured and/or sold by the Company (hereinafter referred to as the Products) assumes that you have read and accepted these terms and conditions which govern your use of the Data. If you do not agree to these terms and conditions, you must stop using this website and the Data. You must not use the Data for any unlawful purpose or in any manner inconsistent with these terms and conditions.
- 1. CAD Data
- The Data is prepared for assisting the Company's users in the CAD design process by providing dimensions and other Product information. In order to provide the best speed and stability working within this site, the Product drawings were simplified to reduce the size of the Data. For instance, some of the Products are shown without the oil groove shape, screws or spring shape. Also, please be aware that the tolerance, surface roughness and/or chamfer of the Data may vary from the actual Products.
- 2. Disclaimer on Data
- While the Company has carefully prepared the Data, accuracy of the Data is not guaranteed and is subject to the variances as described above. The Company may also modify, add or delete the Data at any time without prior notice. The Company assumes no liability for any direct, indirect, consequential or special damages that you may claim resulted from your use of the Data or any changes to or deletions of the Data regardless of the reason. The Company provides no warranty as to the quality, accuracy, functionality, safety or reliability of the combination of Products and parts. Example applications and combinations of the Products are provided for illustrative purposes only.
- 3. Copyright
-
Copyrights to the content and the Data belong to the Company or the manufacturers of the Products. The said copyright is protected by the Copyright Act and international treaties. The use (including duplication, modification, uploading, posting, transmission, distribution, licensing, sales and publishing) of the Data except for the purpose to use the Data described above without prior approval of the Company is not allowed. The Data cannot be used for any purposes (including sales promotion) except for designing your machine. If you violate this provision or the laws or regulations, the Company may prohibit you from the use of the Data, the Company’s site and/or take legal action. So long as you comply with these terms and conditions, the Company grants to you a non-exclusive, non-transferable, revocable license to access and use the Data for the sole purpose of assisting you in designing machines that incorporate products.
- 4. Disclaimer of Warranty
- ANY AND ALL CONTENT APPEARING ON THIS WEB SITE IS PROVIDED FOR INFORMATIONAL PURPOSES ONLY. THIS WEB SITE, ITS CONTENT AND ITS LINKS ARE PROVIDED ON AN "AS IS" AND "AS AVAILABLE" BASIS AND ARE USED ONLY AT YOUR SOLE RISK, TO THE FULLEST EXTENT PERMISSIBLE BY LAW. THE COMPANY DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, OF ANY KIND, REGARDING THIS WEB SITE (INCLUDING ITS CONTENT, HARDWARE, SOFTWARE AND LINKS), INCLUDING AS TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, TITLE, NON INFRINGEMENT, RESULTS, ACCURACY, COMPLETENESS, ACCESSIBILITY, COMPATIBILITY, SECURITY AND FREEDOM FROM COMPUTER VIRUS. THE COMPANY WILL NOT BE LIABLE FOR ANY DAMAGES OR LOSSES, INCLUDING DIRECT, INDIRECT, CONSEQUENTIAL, SPECIAL, INCIDENTAL OR PUNITIVE DAMAGES AND/OR LOST PROFITS, IN CONNECTION WITH USE OF THE INTERNET, THIS WEB SITE, ITS CONTENT OR ITS LINKS
Further, the Company will not be liable to you for any failure or delay by the Company to provide access to the Data or any of its obligations under these terms and conditions where such failure or delay is the direct or indirect result of any circumstances beyond the Company's reasonable control (and the Company's obligations will be suspended for the duration of such circumstances). - 5. Policy of Third Parties
- You may be required to separately agree to third party's policies if you use third party software to create or browse the Data or use a third party’s CAD data. In this case, the Company does not assume any responsibility for defects of such CAD data or the software of the third party or violation of their rights. Understand them before use.
CAD Data Download (Unit Assembly)
CAD Data Download: File Format
Cautions on the CAD data
-
Assembly data shows the assembly drawings in the concept design phase. The sole purpose of the data is to explain the structure and functionality of the assembly and is not considered nor to be used as a final design.
You will need to edit the Data so that it meets your specific design conditions. -
The CAD data unit assembly consists of sub-assemblies.
Each sub-assembly unit can be used as it is or can be edited. - The Data for fabricated parts is based on easy-to-edit dimensions and shapes in sketches and histories.
- The Data including the third-part components are made by the Company.
* The part in the frame is a sub-assembly unit.
-
Your access to the CAD data that MISUMI Corporation (hereinafter referred to as the Company) posts on this site (including 3D CAD data, intermediate 3D CAD data and 2D CAD data; hereinafter referred to as the Data) are of products manufactured and/or sold by the Company (hereinafter referred to as the Products) assumes that you have read and accepted these terms and conditions which govern your use of the Data. If you do not agree to these terms and conditions, you must stop using this website and the Data. You must not use the Data for any unlawful purpose or in any manner inconsistent with these terms and conditions.
-
- * Unit assembly CAD data consists of some sub-assemblies.
Each sub-assembly unit can be used as it is or can be edited.
Application Overview
Purpose
- Purpose
- To clamp workpieces that are vulnerable to impact.
- Operation
- Slide shaft mechanism in clamp helps prevent hard impact of the workpiece being clamped.
- To release the workpiece, first release the knob to disengage the slide shaft, then lift the clamp.
Points for use
- Manual operation
Target workpiece
- Shape: glass circuit board
- Size: W65 x L130 x H0.7mm
- Weight: 10.6g
Design Specifications
Operating Conditions or Design Requirements
- Slide shaft stroke: 10mm
Arm rotation angle: 90° - Outer dimensions: W200 x D380 x H144mm
Required Performance
- Clamping force: 3 to 4N
Selection Criteria for Main Components
- A spring with a spring constant k = 0.16N/mm that satisfies the workpiece clamping force requirement of 3 to 4N is selected.
Design Evaluation
Verification of main components
- The clamping force is verified based on the load moment.
- Confirmation of workpiece clamping force
- Conditional value: distance between rotary shaft and center of gravity of arm Lg = 87.4mm, angle formed by rotary shaft and center of gravity of arm α = 15.3°, mass of arm M = 436.9g, gravitational acceleration g = 9.8m/s², distance between rotary shaft and spring post of arm Lk1 = 95.52mm, angle formed by spring post of link base and spring post of arm and rotary shaft β = 20.69°, distance between spring post of link base and spring post of arm Lk2 = 111.4mm, spring constant k = 0.16N/mm, free length of tension spring Lk0 = 100mm, initial tension of spring F1 = 2.94N, number of springs n = 2 pieces, distance between rotary shaft and clamping part La = 201mm, angle formed by rotary shaft and clamping part γ = 3.27°
- Moment produced by arm mass: Mm = (M x g x cosα) x Lg, hence, Mm = 436.9 x 10⁻³ x 9.8 x 0.964 x 87.4 = 360.74N･mm
Moment produced by tension spring: Mk = {k x (Lk2 - Lk0) + F1} x sinβ x Lk1 x n, hence, Mk = {0.16 x (111.4 - 100) + 2.94} x 0.353 x 95.52 x 2 = 321.26N･mm - Comparison of moment
If we put F as the force of the clamping part and Ma as the moment of the clamping part, from Mm + Mk = Ma = F x cosγ x La, F = (Mm + Mk)/(cosγ x La), hence, F = (360.74 + 321.26)/(0.998 x 201) = 3.39N
-> The clamping force is within the target range (3 to 4N).
Other Design Consideration
- The shape of the stopper makes it possible to fix the slide shaft during clamping, and it is automatically returned by the coil spring built in the spring plunger during unclamping.
Explore Similar Application Examples
Page
-
/
-
Payment Method
On-Demand Manufacturing
Certificates
Copyright © MISUMI Corporation All Rights Reserved.