Adjuster Pads（Page 2）

?* Information on days to ship and prices

• • Promotional pricing ends 30/11/2024

  

  Bull's Eye Levels / GN 2277 / K Colourless-transparent

  GANTER

  Bull´s eye levels GN 2277 are used to check the horizontal position of jigs, machines, devices, appliances and instruments.
  The spirit levels are aligned in relation to the reference surface so that the bubble is located inside the marking ring when the horizontal position of the contact surface is achieved.

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	13.16 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing ends 30/11/2024

  

  Levelling feet with vibration absorbing, Steel

  GANTER

  The specified load in the above table of the levelling feet GN 342.1 is a recommendation up to which the damping element can be permanently subjected.
  This static load equals a thrust on the area of 0,4 N/mm2, at which the damping material reaches its optimum dynamic damping ability. This also takes into account an additional load up to 0,6 N/mm2 in the event of a dynamic load.
  Levelling feet GN 342.1 can not be disassembled.

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	13.76 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• 

  Levelling feet without mounting holes, Hygienic Design

  GANTER

  GN 20 levelling feet without mounting holes are intended for use in hygiene areas. The bottom seal protects the area beneath the foot plate from dirt. For this, the foot must be screwed on using the mounting holes and compressed accordingly. Hygienic fastenings and the correct position of the mounting holes are essential. The sealing ring above the adjustment sleeve enables fastening without dead space. Due to the wiper or the ball seal, the moving components are sealed against the environment.
  The high quality finish prevents adherence of dirt and facilitates cleaning.
  The values listed in the table for static load capacity refer to a purely vertical load in relation to the leveling foot. Under normal operating conditions bending loads or angular loads are not uncommon and result in a reduction of load capacity, which must be taken into consideration.

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	132.30 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• • Promotional pricing ends 30/11/2024

  

  Levelling feet, foot / threaded bushing Stainless Steel

  GANTER

  Levelling feet GN 343.5 cannot be disassembled.

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	11.14 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• 

  Levelling sets, long version

  GANTER

  Levelling sets GN 350 are used for levelling and linking operations. They comprise a threaded upper sleeve and a female threaded lower sleeve. The fine thread allows a stepless and precise setting and locking using the C-Spanner DIN 1810. A locking ring serves also as a height limiter for the max. height.
  Normally this screw is permanently and securely locked by the static load created when the mounting screw is tightened.
  Should this not be sufficient, the use of a locknut (Type AK) is recommended.
  

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	39.22 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Levelling sets, short version

  GANTER

  Levelling sets GN 350.1 are used for levelling, adjusting and linking operations if small dimensions are given.
  They comprise a threaded upper sleeve and a female threaded lower sleeve. The fine thread allows a stepless and precise setting and locking using the C-Spanner DIN 1810. A locking ring serves as a height limiter for the max. height.
  

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	31.72 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Levelling feet with fixing lug, Steel, zinc plated, rectangular shape (GN 42)

  GANTER

  GN 42 levelling feet can be used in a host of combinations of base plates and adjustable spindle versions.
  >The levelling feet can be screwed to the mounting surface use the fixing lug, which prevents lateral shifting. Moreover, the types with the rubber underlay protect sensitive surfaces.
  The levelling feet are supplied fully assembled and are not removable.

  • Volume Discount

  Select to compare

  Configure now
  Starting from∗ ：	11.48 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Stainless Steel-Levelling feet with fixing lug, rectangular shape (GN 43)

  GANTER

  GN 43 Stainless Steel-Levelling feet are for use in aggressive environments. The range of combinations of base plates and adjustable spindle versions allows these levelling feat to be used in every situation.
  
  The levelling feet can be screwed to the mounting surface use the fixing lug, which prevents lateral shifting. Moreover, the types with the rubber underlay protect sensitive surfaces.
  
  The levelling feet are supplied fully assembled and are not removable.

  • Volume Discount

  Select to compare

  Configure now
  Starting from∗ ：	14.58 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Euro-Gripper-Tooling - Pedestal 50er, SW50-RD30-L90

  TUENKERS

  Pedestal 50er, SW50-RD30-L90

  • New Product

  Select to compare

  Configure now
  Starting from∗ ：	65.49 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• • Promotional pricing ends 30/11/2024

  

  Anchor Stands for Aluminum Extrusions

  MISUMI

  
  

  • Volume Discount

  • Stock

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	13.57 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• 

  Anchor Bracket

  NIC AUTOTEC

  This is an anchor holder for the aluminium extrusion. There are T-shaped and L-shaped types. [Materials]EN 1.0038 Equiv.

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	16.09 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Rubber Cushion

  NIC AUTOTEC

  A rubber buffer that absorbs shocks. [Material] (1) SBR (2) EN 1.4016 Equiv.

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	5.91 €
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• 

  Rubber Washer

  NIC AUTOTEC

  This is a rubber seat for CLP-60, CLP-120, CLB-120U, CLBS-120U. [Material]Ethylene Propylene Rubber [EPDM].

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	1.29 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Set of AG Series Anchor Connection Brackets AGBK30A

  NIC AUTOTEC

  -AG series safety fence anchor bracket set. Cylindrical bracket (30 mm).

  Select to compare

  Configure now
  Starting from∗ ：	31.67 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Plastic Foot

  YUKI LABORATORY

  [Applications]
  · Attach to the frame T-groove for use.

  • Volume Discount

  2D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	1.32 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• • Promotional pricing ends 30/11/2024

  

  Rubber Feet (Non-Migratory Specifications)

  YUKI LABORATORY

  [Applications]
  · Attach to the frame T-groove for use.

  • Volume Discount

  2D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	2.44 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• 

  Adjuster for Corner

  YUKI LABORATORY

  [Features]
  · Structures can be brought close to each other or installed in corners.

  2D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	6.08 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Adjustment plates for bull´s eye levels GN 2277

  GANTER

  Adjustment plates GN 2277.1 are used in combination with bull´s eye levels GN 2277, Type A.
  The mounting bore holes offset by 120° allow the bull‘s eye levels and the mounting plate to be aligned in relation to the mounting surface. An alignment ball at the bottom surface of the adjustment plate serves as tilting point. Specific tightening torques of the bolts allow to be achieved, so that the bubble is located inside the marking ring once the horizontal alignment is reached.

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	4.02 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Bull's Eye Levels / GN 2279 / ALN, ALS / K Colourless-transparent

  GANTER

  Bull´s eye levels GN 2279 are used to check the horizontal position of jigs, machines, devices, appliances and instruments.
  Type A is used if the spirit level is to be used as a tool, e.g. at different measuring points.
  The spirit levels are aligned in relation to the reference or contact surface, such that the bubble is located inside the marking ring once the horizontal position of the contact surface is reached.

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	10.76 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• • Promotional pricing ends 30/11/2024

  

  Levelling feet, steel sheet, zinc plated with and without rubber underlay

  GANTER

  Levelling feet GN 40 are easy and very reasonably priced foot design variants.
  Theywill be delivered mounted and are not removable.

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	4.68 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing ends 30/11/2024

  

  Mounts for leveling feet

  GANTER

  GN 349 mounts are used on levelling feet particularly in such cases where a machine shrouding is made of very thin sheet metal.

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	11.98 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• 

  Stainless Steel-Levelling feet, A4, with fixing lug, drop shape (GN 45)

  GANTER

  GN 45 Stainless Steel-Levelling feet are for use in aggressive environments. The range of combinations of base plates and adjustable spindle versions allows these levelling feat to be used in every situation.
  
  The levelling feet can be screwed to the mounting surface use the fixing lug, which prevents lateral shifting. Moreover, the types with the rubber underlay protect sensitive surfaces.
  
  The levelling feet are supplied fully assembled and are not removable.

  • Volume Discount

  Select to compare

  Configure now
  Starting from∗ ：	9.08 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Euro-Gripper-Tooling - Pedestal 80er, SW80-RD30-L90

  TUENKERS

  Pedestal 80er, SW80-RD30-L90

  • New Product

  Select to compare

  Configure now
  Starting from∗ ：	66.85 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Stainless Steel-Cover sleeves, Hygienic Design

  GANTER

  Stainless steel cover sleeves GN 20.1 are certified according to 3-A Sanitary Standards, Inc. guidelines and intended for use in hygienic areas.
  ・These cover protruding male threads while also substituting for lock nuts .The sealed mounting surfaces enable fastening without dead spaces.
  ・The high quality finish prevents adherence of dirt and facilitates cleaning.

  • Volume Discount

  Select to compare

  Configure now
  Starting from∗ ：	21.42 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Levelling feet for aluminium profiles (K0432)

  KIPP

  · Especially suitable for tables and light installations
  
  · Equipment foot height is adjusted by turning the nut by hand or spanner
  
  · Compatible with all conventional aluminium profiles with 8 mm or 10 mm slot width

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	7.50 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Levelling feet for aluminium profiles (27840)

  NORELEM

  · Especially suitable for tables and light installations
  
  · Equipment foot height is adjusted by turning the nut by hand or spanner
  
  · Compatible with all conventional aluminium profiles with 8 mm or 10 mm slot width

  Select to compare

  Configure now
  Starting from∗ ：	9.67 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

Loading...