PLC (Input/Output Units)（Output Format：Other）
| Shipping Days |
|
|---|
?* Information on days to ship and prices
-
Configure now
Starting from∗ ： 495.37 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
NX Series Digital Output Unit NX-OD Transistor Output Unit
OMRON
Digital output unit that is available in many variations, from high-speed types that enable high-speed synchronization control to general-purpose types
■ Features
· Can be mounted on an EtherCAT coupler to enable high-speed I/O refreshing
· Enables I/O refreshing synchronized with the controller control period (synchronous refresh)
· Using this unit in combination with an NX Series CPU Unit or EtherCAT Coupler Unit, an NX unit that uses a time stamping input method,
and an NX unit that uses a time-specific output method enables highly precise I/O control that does not depend on the
controller's control period
· The use of a removable terminal block improves system maintainability
· The Push-In Plus terminal block (screwless clamp terminal block) and connector type (MIL connector / Fujitsu connector)
greatly reduce the time required for wiring work
· A unit width of only 12 mm realizes space saving (connector type 30 mm)
· 2-, 4-, 8-, 16- and 32-output-contact types are available, enabling the I/O configuration that best suits your equipment
· Connect to the CJ Series using the EtherNet/IP couplerConfigure nowStarting from∗ ： 136.54 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
NX Series Incremental Encoder Input Unit NX-EC0□□□
OMRON
Enables more precise timing control by synchronizing the encoder data with the time data
■ Features
· Open-collector-output type and line-driver-output type incremental encoders can be connected
· High-speed remote I/O control with communications cycle as fast as 125 μs*1
· Free-run refreshing, synchronous I/O refreshing, or
task period prioritized refreshing*2 with the NX1P2 CPU Unit or EtherCAT Coupler Unit
· The MC Function Module of the NJ/NX/NY5 Controllers allows the encoder
to be used as a motion axis
· Latching (1 internal signal and 2 input signals from external devices)
· Pulse period measurement
· 32-bit counters (80000000 to 7FFFFFFF HEX)
· Maximum counting rate: 4 MHz (Line receiver: 4 MHz; Open collector: 500 kHz)
· Time stamping
· Maximum and minimum counter value setting
· Connect to the CJ PLC using the EtherNet/IP coupler
*1 When using the NX-EC01□□ together with the NX701-□□□□ and NX-ECC203.
*2 Task period prioritized refreshing is available when the NX-ECC203 is used together.Configure nowStarting from∗ ： 642.92 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
NX Series Position Interface Pulse Output Unit NX-PG0□□□
OMRON
Positioning control with pulse outputs to command stepper motor drives and other pulse input motor drives
■ Features
· The MC Function Module of the NJ/NX/NY5 Controller allows you to
connect with as many axes as the NJ/NX/NY5 Controller can control
· High-speed remote I/O control with communications cycle as fast as 125 μs*1
· Multiple stepping motors and servo motors can be operated in synchronization by
using synchronous I/O refreshing or task period prioritized refreshing*2
· Latching (2 external latch inputs)
· Open collector pulse outputs up to 500 kHz
or line driver pulse outputs up to 4 MHz
· Line driver output models with 2 or 4 channels
*1 When using the NX-EC01□□ together with the NX701-□□□□ and NX-ECC203.
* *2 Task period prioritized refreshing is available when the NX-ECC203 is used together.Configure nowStarting from∗ ： 643.55 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
![Smart DeviceNet I/O [DRT2]](//uk.misumi-ec.com/linked/material/el/OMR1/PHOTO/222304232673_001.jpg?$product_view_b$)
Smart DeviceNet I/O [DRT2]
OMRON
Smart DeviceNet I/O
Compact DeviceNet I/O units with extensive diagnostic functions. Data regarding power supply status, I/O response times, operation counters and on-time are continuously recorded and checked against user-defined limits. Any deviation is reported to the control system, as indication to perform machine maintenance and prevent unplanned downtime. Smart DeviceNet I/Os are supported by PLC Function Blocks and HMI Smart Active Parts, allowing program-less visualisation and monitoring from the CJ1 PLCs and NS operator terminals.
• Compact size IP20 housing
• Expandable digital I/Os
• Built-in diagnostics and preventive maintenance functions
• Detachable I/O terminal blocks
• Analog I/O with data pre-processing and alarm functionsConfigure nowStarting from∗ ： 663.07 € Min. Shipping Days ： 3 Days *Unit price with basic configuration
-
![Digital I/O Slave Unit with Clamp Terminals [CRT1-□D16SL(-1)]](//uk.misumi-ec.com/linked/material/el/OMR1/PHOTO/222304232684_001.jpg?$product_view_b$)
Digital I/O Slave Unit with Clamp Terminals [CRT1-□D16SL(-1)]
OMRON
Screw-less Terminal Wiring Further Reduces Wiring Work and Saves Labor at the Production Site.
• Screw-less (M3) design reduces the need for extra tightening.
• Removable terminal block gives powerful support to maintenance work.
• One-step wiring. Wire simply by inserting the ferrules.
• Applicable wire: AWG24 to AWG16 (cross-section: 0.2 to 1.25 mm²Configure nowStarting from∗ ： 837.33 € Min. Shipping Days ： 3 Days *Unit price with basic configuration
-
SmartSlice I/O System, I/O Units
OMRON
The smartest modular I/O system
OMRON's SmartSlice I/O system is compact, intelligent and easy. When used with OMRON's CS1/CJ1 DeviceNet or CompoNet master units, no configuration tool is required. By using built-in functions such as pre-scaling, totalising, differentiation and alarming in analog I/O units, PLC programming can be minimised. Preventive maintenance data collected by all I/O units can be accessed using CX-Integrator or NS-series Smart Active Parts.
• Most compact in the market (84 mm high)
• Easy set-up, backup and restore functions
• Diagnostics and preventive maintenance data at I/O level
• Detachable terminal blocks allow hot-swapping without re-wiring
• 3-wire I/O connection with 'push-in' technology, no screwdriver requiredConfigure nowStarting from∗ ： 166.40 € Min. Shipping Days ： 3 Days *Unit price with basic configuration
![Smart DeviceNet I/O [DRT2]](http://uk.misumi-ec.com/linked/material/el/OMR1/PHOTO/222304232673_001.jpg?$product_view_b$)
![Digital I/O Slave Unit with Clamp Terminals [CRT1-□D16SL(-1)]](http://uk.misumi-ec.com/linked/material/el/OMR1/PHOTO/222304232684_001.jpg?$product_view_b$)
| Brand |
|---|
| Product Series |
| Starting from∗ |
| Min. Shipping Days |
| Number Of Inputs |
| Input Format |
| Rated Input Voltage(V) |
| Number of Outputs |
| Output Format |
| Rated load voltage(V) |
| Protection function |
| Connection Terminal |
| Representative Standard |
|
|
|
|
|
|
| |
| Brand | OMRON | OMRON | OMRON | OMRON | OMRON | OMRON | OMRON |
| Product Series | Digital I/O Slave Unit with Clamp Terminals [CRT1-□D16SL(-1)] | ||||||
| Starting from∗ | 495.37 € *Unit price with basic configuration Volume Discount | 136.54 € *Unit price with basic configuration | 642.92 € *Unit price with basic configuration | 643.55 € *Unit price with basic configuration | 663.07 € *Unit price with basic configuration | 837.33 € *Unit price with basic configuration | 166.40 € *Unit price with basic configuration |
| Min. Shipping Days | 6 Days | 6 Days | 6 Days | 6 Days | 3 Days | 3 Days | 3 Days |
| Number Of Inputs | 32 | - | - | - | 8 | - | - |
| Input Format | DC input | - | - | - | DC input | - | DC input |
| Rated Input Voltage(V) | 24 | - | - | - | - | - | - |
| Number of Outputs | - | 32 | - | - | 8 ～ 16 | 16 | 4 ～ 8 |
| Output Format | Other | Other | Other | Other | Other | Other | Other |
| Rated load voltage(V) | - | - | - | - | - | - | - |
| Protection function | - | - | - | - | - | - | - |
| Connection Terminal | Terminal Block | Terminal Block | - | - | - | - | - |
| Representative Standard | - | CE / UL / CUL / CSA | CE / UL / CUL / CSA | CE / UL / CUL / CSA | CE / Other | CE / Other | - |
![Smart DeviceNet I/O [DRT2]](http://uk.misumi-ec.com/linked/material/el/OMR1/PHOTO/222304232673_001.jpg?$product_view_c$)
![Digital I/O Slave Unit with Clamp Terminals [CRT1-□D16SL(-1)]](http://uk.misumi-ec.com/linked/material/el/OMR1/PHOTO/222304232684_001.jpg?$product_view_c$)
Loading...
Filter by:
-
Number Of Inputs
-
Input Format
- DC input
- AC input
- AC/DC input
- Other
-
Rated Input Voltage(V)
-
Number of Outputs
-
Output Format
- Relay contact output
- Triac output
- Transistor / source output
- Transistor / sync output
- Other
-
Rated load voltage(V)
-
Protection function
- None
- Output protection function
- Other
-
Connection Terminal
- Terminal Block
- Connector
-
Representative Standard
- CE
- UL
- CUL
- TUV
- CSA
- Other
Brand
CAD data type
-
- 2D
- 3D
Categories related to PLC (Input/Output Units)
-
- PLC (CPU Units)
- PLC (Expansion Units)
- PLC (Power Supply Units)
- PLC (Base Units)
- PLC (Software, Manuals)
- PLC Compatible Cables
- PLC Compatible Batteries
- PLC (Options, Others)
- PLC (Communication Units)
- PLC (Input/Output Units)
- PLC (Analog Units)
- PLC (Memory Units)
- PLC (Motion Controllers)
- PLC (Control Units)
- PLC (Wire-Saving Dedicated Units)
-
Metoda płatności
Faktura
Przedpłata
Produkcja na zamówienie
Certyfikaty
Copyright © MISUMI Corporation All Rights Reserved.