Plates / Ceramic PUR / Ether, Ester / A50, A70, A90, A95 / adhesive layer

View the FAQ (5)

MISUMI

Part Number

Once your search is narrowed to one product,
the corresponding part number is displayed here.

Drawing / Specifications
3D Preview 3D preview is available after complete configuration
Part Numbers
More Information
Catalog
Technical Information

Back to the Category Panels (polyurethane rubber, rubber, foam, felt)

Technical Drawing - Panels (polyurethane rubber, rubber, foam, felt)

Open the technical drawing in the new window

Available dimensions and tolerances can be found under the tab More information.

Basic Properties (e.g., material, hardness, coating, tolerance) - Panels (polyurethane rubber, rubber, foam, felt)

Type	Type		Material	Hardness	Color
	No Adhesive	Adhesive
Mold Surface Type	UTSCS	UTSCSA	Ceramic Urethane (Ether Polyurethane)	Shore A95	Natural Color (Gray)
	UTSCH	UTSCHA		Shore A90
	UTSCM	UTSCMA	Ceramic Urethane (Ester Polyurethane)	Shore A70
	UTSCL	UTSCLA		Shore A50
Machined Surface Type	UTSCSK	UTSCSKA	Ceramic Urethane (Ether Polyurethane)	Shore A95
	UTSCHK	UTSCHKA		Shore A90
	UTSCMK	UTSCMKA	Ceramic Urethane (Ester Polyurethane)	Shore A70
	UTSCLK	UTSCLKA		Shore A50

Properties >> P.389
Mold Surface Type has glossy smooth surface but not slippery. Machined Surface Type has ground surface on one side improving sliding property.

Further specifications can be found under the tab More information.

Composition of a Product Code - Panels (polyurethane rubber, rubber, foam, felt)

■Standard

Part Number	-	A	-	B
UTSCLK5	-	100	-	30

■Hole Type

Part Number	-	A	-	B	-	F	-	G	-	Screw Nominal Dia.
UTSCMK2H5	-	100	-	50	-	F80	-	G25	-	N3

General Information - Panels (polyurethane rubber, rubber, foam, felt)

Selection details of panels (polyurethane rubber, rubber, foam, felt)

- Material: polyurethane rubber (PU/PUR), heat-resistant polyurethane rubber, low-impact polyurethane rubber, abrasion-resistant polyurethane rubber, antistatic polyurethane, nitrile (NBR), chloroprene rubber (CR), polyethylene (EPDM), silicone (SI), fluorine (FPM), butyl rubber (IIR), natural rubber (NR), hard rubber, special synthetic rubber, polyurethane foam, head-insulating foam, polyethylene foam, low-rebound foam

- Thickness (mm): 0.5 to 50

- Width (mm): 3 to 500

- Length (mm): 10 to 2000

Description/Basics

Foam plates and rubber plates are provided for damping or for sound proofing. MISUMI offers these in various Shore hardening for a wide variety of tasks. Due to the variety of materials, different resistances to environmental influences are possible depending on the application. The foam plates reduce sound in machines and can reduce the sound emissions of a system. For more information on foam characteristics, follow this link.
Rubber plates or foam plates are also suitable in conveyor systems to absorb components to be transported at a dampened level or to protect them from damage as a lateral guide when the components bump into each other. Hard rubber panels or low-impact rubber or foam panels reduce the impact energy of the components. These minimize and lower the vibrations in an application.
In addition, MISUMI offers highly abrasion-resistant polyurethane (Vulkollan), which has an abrasion resistance that is six times higher than with conventional polyurethane.
Ceramic polyurethane plates contain ceramic particles. After machining, these can have a smooth surface despite low Shore hardness.
The polyurethane rubber plates are also available antistatically. The specific resistance of antistatic polyurethane plates prevents static charging. This prevents any damage to electronic components.
For applications with higher temperatures, MISUMI offers heat-resistant polyurethane rubber, which can withstand a temperature range of up to approx. ~120°C (see the product specifications for exact information).
MISUMI also offers low-friction and anti-friction rubber plates. Low-friction rubber plates are often used in the gentle component guide for belt conveyors and roller conveyors.
Felt plates have the property of absorbing or dispensing oil and other liquids via the capillary effect. This property can be used to remove, for example, excess oil on a belt conveyor.

In addition, MISUMI offers rubber plates and foam plates that are self-adhesive for simplified assembly. Furthermore, you will find double-adhesive tape for attaching rubber plates and foam plates.

Additional properties on foam panels and rubber plates can be found in the Properties PDF.

MISUMI also offers these products in a round shape as discs and sleeves made of rubber, natural rubber, foam and felt.

Application Examples - Panels (polyurethane rubber, rubber, foam, felt)

Application example
(1) Low-friction rubber plate (2) belt conveyor

Application example
(1) Vibration damping plate

Industrial Applications

3D printer industry

Automotive industry

Pharmaceutical industry

Packaging industry

Part Number:

3D preview is not available, because the part number has not yet been determined.

In order to open the 3D preview, the part number must be fixed.

Plug-in is required for 3D Preview

CAD Download

Data to be displayed: 30; 45; 60

1
2
3
4
5
Next >>

Part Number
UTSCH1H2-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH1H3-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH1H4-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH1H5-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH1H6-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH1H8-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH1H8-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-Z3
UTSCH1H10-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH1H10-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-Z[3,4]
UTSCH2-[10-500/1]-[10-500/1]
UTSCH2H2-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH2H3-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH2H4-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH2H5-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH2H6-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH2H8-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH2H8-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-495/0.5]-Z3
UTSCH2H10-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH2H10-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-495/0.5]-Z[3,4]
UTSCH3-[10-500/1]-[10-500/1]
UTSCH3H2-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH3H3-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH3H4-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH3H5-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH3H6-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH3H8-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH3H8-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-495/0.5]-Z3
UTSCH3H10-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCH3H10-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-495/0.5]-Z[3,4]
UTSCH4-[10-500/1]-[10-500/1]
UTSCH4H2-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-491/0.5]-N[3,4,5,6,8,10]
UTSCH4H3-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-491/0.5]-N[3,4,5,6,8,10]
UTSCH4H4-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-491/0.5]-N[3,4,5,6,8,10]
UTSCH4H5-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-491/0.5]-N[3,4,5,6,8,10]
UTSCH4H6-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-491/0.5]-N[3,4,5,6,8,10]
UTSCH4H8-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-491/0.5]-N[3,4,5,6,8,10]
UTSCH4H8-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-491/0.5]-Z3
UTSCH4H10-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-491/0.5]-N[3,4,5,6,8,10]
UTSCH4H10-[25-500/1]-[25-500/1]-F[9-491/0.5]-G[5-491/0.5]-Z[3,4]
UTSCH5-[10-500/1]-[10-500/1]
UTSCH6-[10-500/1]-[10-500/1]
UTSCH6H2-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-491/0.5]-N[3,4,5,6,8,10]
UTSCH6H3-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-491/0.5]-N[3,4,5,6,8,10]
UTSCH6H4-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-491/0.5]-N[3,4,5,6,8,10]
UTSCH6H5-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-491/0.5]-N[3,4,5,6,8,10]
UTSCH6H6-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-491/0.5]-N[3,4,5,6,8,10]
UTSCH6H8-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-491/0.5]-N[3,4,5,6,8,10]
UTSCH6H8-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-491/0.5]-Z3
UTSCH6H10-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-491/0.5]-N[3,4,5,6,8,10]
UTSCH6H10-[25-500/1]-[25-500/1]-F[9-245/0.5]-G[5-491/0.5]-Z[3,4]
UTSCH8-[10-500/1]-[10-500/1]
UTSCH10-[10-500/1]-[10-500/1]
UTSCHA1H2-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCHA1H3-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCHA1H4-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCHA1H5-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCHA1H6-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCHA1H8-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]
UTSCHA1H8-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-Z3
UTSCHA1H10-[25-500/1]-[25-500/1]-F[5-491/0.5]-G[5-495/0.5]-N[3,4,5,6,8,10]

Standard Unit Price	Minimum order quantity	Standard Shipping Days ?	RoHS	With or w/o Adhesive	Thickness T (mm)	Width A (mm)	Length B (mm)	Hardness (Shore, Asker, Penetration)	Specifications	Hole Machining	Counterbored Hole Nominal Dia. [Z]	F (mm)	G (mm)	Through Hole Nominal Dia. [N]
-	1	9 Days	10	No Adhesive	2	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	-	5 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	3	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	-	5 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	4	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	-	5 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	5	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	-	5 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	6	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	-	5 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	8	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	-	5 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	8	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	3	5 ～ 491	5 ～ 495	-
-	1	9 Days	10	No Adhesive	10	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	-	5 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	10	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	3 ～ 4	5 ～ 491	5 ～ 495	-
-	1	9 Days	10	No Adhesive	2	10 ～ 500	10 ～ 500	Shore A90	Mold Surface / Standard Type	No Drilling Alteration	-	-	-	-
-	1	9 Days	10	No Adhesive	2	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	2H (Two Holes)	-	9 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	3	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	2H (Two Holes)	-	9 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	4	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	2H (Two Holes)	-	9 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	5	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	2H (Two Holes)	-	9 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	6	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	2H (Two Holes)	-	9 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	8	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	2H (Two Holes)	-	9 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	8	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	2H (Two Holes)	3	9 ～ 491	5 ～ 495	-
-	1	9 Days	10	No Adhesive	10	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	2H (Two Holes)	-	9 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	10	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	2H (Two Holes)	3 ～ 4	9 ～ 491	5 ～ 495	-
-	1	9 Days	10	No Adhesive	3	10 ～ 500	10 ～ 500	Shore A90	Mold Surface / Standard Type	No Drilling Alteration	-	-	-	-
-	1	9 Days	10	No Adhesive	2	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	3H (Three Holes)	-	9 ～ 245	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	3	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	3H (Three Holes)	-	9 ～ 245	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	4	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	3H (Three Holes)	-	9 ～ 245	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	5	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	3H (Three Holes)	-	9 ～ 245	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	6	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	3H (Three Holes)	-	9 ～ 245	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	8	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	3H (Three Holes)	-	9 ～ 245	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	8	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	3H (Three Holes)	3	9 ～ 245	5 ～ 495	-
-	1	9 Days	10	No Adhesive	10	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	3H (Three Holes)	-	9 ～ 245	5 ～ 495	3 ～ 10
-	1	9 Days	10	No Adhesive	10	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	3H (Three Holes)	3 ～ 4	9 ～ 245	5 ～ 495	-
-	1	9 Days	10	No Adhesive	4	10 ～ 500	10 ～ 500	Shore A90	Mold Surface / Standard Type	No Drilling Alteration	-	-	-	-
-	1	9 Days	10	No Adhesive	2	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	4H (Four Holes)	-	9 ～ 491	5 ～ 491	3 ～ 10
-	1	9 Days	10	No Adhesive	3	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	4H (Four Holes)	-	9 ～ 491	5 ～ 491	3 ～ 10
-	1	9 Days	10	No Adhesive	4	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	4H (Four Holes)	-	9 ～ 491	5 ～ 491	3 ～ 10
-	1	9 Days	10	No Adhesive	5	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	4H (Four Holes)	-	9 ～ 491	5 ～ 491	3 ～ 10
-	1	9 Days	10	No Adhesive	6	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	4H (Four Holes)	-	9 ～ 491	5 ～ 491	3 ～ 10
-	1	9 Days	10	No Adhesive	8	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	4H (Four Holes)	-	9 ～ 491	5 ～ 491	3 ～ 10
-	1	9 Days	10	No Adhesive	8	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	4H (Four Holes)	3	9 ～ 491	5 ～ 491	-
-	1	9 Days	10	No Adhesive	10	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	4H (Four Holes)	-	9 ～ 491	5 ～ 491	3 ～ 10
-	1	9 Days	10	No Adhesive	10	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	4H (Four Holes)	3 ～ 4	9 ～ 491	5 ～ 491	-
-	1	9 Days	10	No Adhesive	5	10 ～ 500	10 ～ 500	Shore A90	Mold Surface / Standard Type	No Drilling Alteration	-	-	-	-
-	1	9 Days	10	No Adhesive	6	10 ～ 500	10 ～ 500	Shore A90	Mold Surface / Standard Type	No Drilling Alteration	-	-	-	-
-	1	9 Days	10	No Adhesive	2	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	6H (Six Holes)	-	9 ～ 245	5 ～ 491	3 ～ 10
-	1	9 Days	10	No Adhesive	3	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	6H (Six Holes)	-	9 ～ 245	5 ～ 491	3 ～ 10
-	1	9 Days	10	No Adhesive	4	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	6H (Six Holes)	-	9 ～ 245	5 ～ 491	3 ～ 10
-	1	9 Days	10	No Adhesive	5	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	6H (Six Holes)	-	9 ～ 245	5 ～ 491	3 ～ 10
-	1	9 Days	10	No Adhesive	6	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	6H (Six Holes)	-	9 ～ 245	5 ～ 491	3 ～ 10
-	1	9 Days	10	No Adhesive	8	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	6H (Six Holes)	-	9 ～ 245	5 ～ 491	3 ～ 10
-	1	9 Days	10	No Adhesive	8	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	6H (Six Holes)	3	9 ～ 245	5 ～ 491	-
-	1	9 Days	10	No Adhesive	10	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	6H (Six Holes)	-	9 ～ 245	5 ～ 491	3 ～ 10
-	1	9 Days	10	No Adhesive	10	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	6H (Six Holes)	3 ～ 4	9 ～ 245	5 ～ 491	-
-	1	9 Days	10	No Adhesive	8	10 ～ 500	10 ～ 500	Shore A90	Mold Surface / Standard Type	No Drilling Alteration	-	-	-	-
-	1	9 Days	10	No Adhesive	10	10 ～ 500	10 ～ 500	Shore A90	Mold Surface / Standard Type	No Drilling Alteration	-	-	-	-
-	1	9 Days	10	Adhesive	2	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	-	5 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	Adhesive	3	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	-	5 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	Adhesive	4	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	-	5 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	Adhesive	5	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	-	5 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	Adhesive	6	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	-	5 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	Adhesive	8	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	-	5 ～ 491	5 ～ 495	3 ～ 10
-	1	9 Days	10	Adhesive	8	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	3	5 ～ 491	5 ～ 495	-
-	1	9 Days	10	Adhesive	10	25 ～ 500	25 ～ 500	Shore A90	Mold Surface / Hole Type	1H (1-Hole)	-	5 ～ 491	5 ～ 495	3 ～ 10

1
2
3
4
5
Next >>

Back to the Category Panels (polyurethane rubber, rubber, foam, felt)

Technical Drawing - Panels (polyurethane rubber, rubber, foam, felt)

Open the technical drawing in the new window

Specification Tables - Panels (polyurethane rubber, rubber, foam, felt)

■Accuracy Standards
T Dimension Tolerance

T	Tolerance
	Mold Surface Type	Machined Surface Type
2~4	±0.3	±0.5
5~10	±0.4

A, B Tolerance

A, B	Tolerance
200 or Less	±0.5
201~300	±1.0
301~400	±1.2
401~500	±1.5

■Standard Type, Mold Surface

Part Number				1mm Increment
Type			T	A	B
			2	10~500	10~500
No Adhesive	Adhesive		3
UTSCS	UTSCSA	(Shore A95)	4
UTSCH	UTSCHA	(Shore A90)	5
UTSCM	UTSCMA	(Shore A70)	6
UTSCL	UTSCLA	(Shore A50)	8
			10

■Standard Type, Machined Surface

Part Number				1mm Increment
Type			T	A	B
No Adhesive UTSCSK UTSCHK UTSCMK UTSCLK	Adhesive UTSCSKA UTSCHKA UTSCMKA UTSCLKA	(Shore A95) (Shore A90) (Shore A70) (Shore A50)	3	10~200	10~200
			4
			5
			6
			8
			10

■Hole Type, Mold Surface

Part Number					1mm Increment (A≥B≥T)		0.5mm Increment		Screw Nominal Dia. Selection
Type			Nominal	T	A	B	F	G	N (Through Hole)	Z (Counterbored Hole)
Mold Surface Type			1H 2H 3H 4H 6H	2	25~500	25~500	5~495 (1H) 9~491 (2H, 4H) 9~245 (3H, 6H)	5~495 (1H, 2H, 3H) 9~491 (4H, 6H)	3 4 5 6 8 10	-
No Adhesive UTSCS UTSCH UTSCM UTSCL	Adhesive UTSCSA UTSCHA UTSCMA UTSCLA	(Shore A95) (Shore A90) (Shore A70) (Shore A50)		3						-
				4						-
				5						-
				6						-
				8						3
				10						3	4

■Hole Type, Machined Surface

Part Number					1mm Increment (A≥B≥T)		0.5mm Increment		Screw Nominal Dia. Selection
Type			Nominal	T	A	B	F	G	N (Through Hole)	Z (Counterbored Hole)
Machined Surface Type			1H 2H 3H 4H 6H	3	25~200	25~200	5~195 (1H) 9~191 (2H, 4H) 9~95 (3H, 6H)	5~195 (1H, 2H, 3H) 9~191 (4H, 6H)	3 4 5 6 8 10	-
No Adhesive UTSCSK UTSCHK UTSCMK UTSCLK	Adhesive UTSCSKA UTSCHKA UTSCMKA UTSCLKA	(Shore A95) (Shore A90) (Shore A70) (Shore A50)		4						-
				5						-
				6						-
				8						3
				10						3	4

Products homepage

Basic information

Material	Urethane	Grade, Type	Ceramic Urethane

Configure

784Suggestion of an applicable part number.

View Part Numbers

Some specification is not specified yet.

The part number is completed.

Basic Attributes

With or w/o Adhesive
- Adhesive
- No Adhesive
Clear
Thickness T(mm)
2

3

4

5

6

8

10
Clear
Width A(mm)
[10-500/1mm Unit(s)]
Clear
Length B(mm)
[10-500/1mm Unit(s)]
Clear
Hardness (Shore, Asker, Penetration)
Shore A50

Shore A70

Shore A90

Shore A95
Clear
Specifications
Machined Surface / Hole Type

Machined Surface / Standard Type

Mold Surface / Hole Type

Mold Surface / Standard Type
Clear
Hole Machining
- 1H (1-Hole)
- 2H (Two Holes)
- 3H (Three Holes)
- 4H (Four Holes)
- 6H (Six Holes)
- No Drilling Alteration
Clear
Counterbored Hole Nominal Dia. [Z]
3

4
Clear
F(mm)
[5-491/0.5mm Unit(s)]
Clear
G(mm)
[5-495/0.5mm Unit(s)]
Clear
Through Hole Nominal Dia. [N]
3

4

5

6

8

10
Clear
Type
- UTSCH
- UTSCH1H
- UTSCH2H
- UTSCH3H
- UTSCH4H
- UTSCH6H
- UTSCHA
- UTSCHA1H
- UTSCHA2H
- UTSCHA3H
- UTSCHA4H
- UTSCHA6H
- UTSCHK
- UTSCHK1H
- UTSCHK2H
- UTSCHK3H
- UTSCHK4H
- UTSCHK6H
- UTSCHKA
- UTSCHKA1H
- UTSCHKA2H
- UTSCHKA3H
- UTSCHKA4H
- UTSCHKA6H
- UTSCL
- UTSCL1H
- UTSCL2H
- UTSCL3H
- UTSCL4H
- UTSCL6H
- UTSCLA
- UTSCLA1H
- UTSCLA2H
- UTSCLA3H
- UTSCLA4H
- UTSCLA6H
- UTSCLK
- UTSCLK1H
- UTSCLK2H
- UTSCLK3H
- UTSCLK4H
- UTSCLK6H
- UTSCLKA
- UTSCLKA1H
- UTSCLKA2H
- UTSCLKA3H
- UTSCLKA4H
- UTSCLKA6H
- UTSCM
- UTSCM1H
- UTSCM2H
- UTSCM3H
- UTSCM4H
- UTSCM6H
- UTSCMA
- UTSCMA1H
- UTSCMA2H
- UTSCMA3H
- UTSCMA4H
- UTSCMA6H
- UTSCMK
- UTSCMK1H
- UTSCMK2H
- UTSCMK3H
- UTSCMK4H
- UTSCMK6H
- UTSCMKA
- UTSCMKA1H
- UTSCMKA2H
- UTSCMKA3H
- UTSCMKA4H
- UTSCMKA6H
- UTSCS
- UTSCS1H
- UTSCS2H
- UTSCS3H
- UTSCS4H
- UTSCS6H
- UTSCSA
- UTSCSA1H
- UTSCSA2H
- UTSCSA3H
- UTSCSA4H
- UTSCSA6H
- UTSCSK
- UTSCSK1H
- UTSCSK2H
- UTSCSK3H
- UTSCSK4H
- UTSCSK6H
- UTSCSKA
- UTSCSKA1H
- UTSCSKA2H
- UTSCSKA3H
- UTSCSKA4H
- UTSCSKA6H
Clear
Filter by CAD data type
- 2D
- 3D
Clear

Optional Attributes

The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .

Frequently Asked Questions (FAQ)

Question:
How can you attach a rubber plate?: Answer:
A rubber plate can be attached with double-adhesive tape. MISUMI offers rubber plates with configurable through holes or counterbores with adhesive tape.
Question:
Do you have screw-on rubber panels?: Answer:
MISUMI offers rubber plates that can be screwed on via a through hole or counterbore. The rubber plates with counterbores are well suited for applications that need to form a flat surface.
Question:
Is NBR oil-resistant?: Answer:
The NBR rubber is oil-resistant and is often used as a sealing material for rubber or foam. In addition, NBR has good thermal resistance, which in combination with high abrasion resistance is the best suited NBR material for seals.
Question:
Which material reduces vibrations well?: Answer:
Silicone gel vibration dampers reduce vibrations well. This elastic material reduces the transmission of vibrations to the subsequent component and also contributes to the acoustics.
Question:
What is Vulkollan?: Answer:
Vulkollan is a highly abrasion-resistant polyurethane rubber that has high wear resistance. It is one of the high-performance rubbers that has little pressure deformation and can withstand high impact forces. In addition, Vulkollan has a high tear strength. However, over time Vulkollan may change its colour, but without losing its mechanical properties.